1990s hood on an old duct
Original 1990s ventilation was sized for a different era of cooking. A modern hood often needs a larger duct and a new exterior cap.
Serving Batavia & nearby Geneva, St. Charles
Range Hood Installation in Batavia, IL
We install under-cabinet, wall chimney, island and insert range hoods in Batavia, ducted outside wherever the house allows.
- Installers working in Batavia ZIP 60510, 60539
- Hookups by licensed trades where the code calls for it
- Old unit hauled away on request
Range hood installs we handle in Batavia
Most kitchen ventilation complaints come from the install, not the hood: a duct that is too small, a long run full of elbows, or a fan that blows grease into the cabinet above. Our Batavia installers set the hood, the duct and the exterior cap as one system.
Long duct run with many elbows
A duct that snakes across the ceiling to a far wall can starve even a strong fan. We look for a shorter path, sometimes straight up through the roof.
Island hood over a new island cooktop
Ventilating an island takes more planning than a wall hood: ceiling support, joist direction and the path out all decide where the hood can go.
Hood that vents into the attic or soffit
We sometimes find an old hood ending in the attic with no cap at all. The duct is carried through to the outdoors and fitted with a damper.
Custom hood cover that needs an insert
If your cabinetmaker built a decorative hood, the working part is a hood insert. We fit it, duct it outside and wire it to the switch.
Gas range that needs stronger ventilation
Pro-style gas ranges with high-output burners often need a larger hood and a bigger duct. We follow the range and hood makers' guidance.
High-CFM hood and makeup air
Very powerful hoods can pull more air out of a tight house than leaks back in. High-CFM hoods can trigger a makeup-air requirement under local code, and we check that before you choose one.
Duct too small for the new hood
Many older hoods ran on a small round or rectangular duct. A stronger hood often calls for a larger duct, and squeezing it into the old one makes it loud and weak.
What the install includes
- Removing the old hoodWe take out the old unit and check what is behind it before the new one goes up.
- Blocking and mountingMounting points set at the height in the maker's instructions.
- Duct runA short, direct duct with as few elbows as possible.
- Wall cap or roof jackThe duct ends outside under a damper that closes when the fan is off.
- Electrical connectionThe hood connected to a suitable circuit; new wiring or switches are run by an electrician.
- Recirculating setupDuctless installs get the maker's charcoal filter kit and a clear plan for replacing it.
- Test and cleanupEvery fan speed and light tested, the damper checked from outside, the area cleaned up.
Models, parts and fittings
Duct, caps and dampersRigid galvanized or stainless duct, wall caps and roof jacks with backdraft dampers.
Under-cabinet hoodsThe most common style, tucked under the upper cabinet above the range.
Wall chimney hoodsA canopy on the wall with a chimney cover hiding the duct up to the ceiling.
Island hoodsHoods suspended above an island, supported from the ceiling framing.
Internal and remote blowersA remote blower moves the motor away from the cooktop for a quieter hood.
What the work looks like in Batavia homes
Before
Installed
DetailBatavia kitchen, 1990s two-story colonial: range hood installation
The site: a 1990s two-story colonial in Batavia. The kitchen as it was: black appliances and golden-oak cabinets with oak soffits above. The reason for the call: cooking smells that stayed in the house for hours. Finished kitchen: a new stainless chimney range hood ducted to the outside. On site this meant blocking and mounting, wall cap or roof jack, plus test and cleanup.
Before
AfterRange Hood Installation in a 1990s two-story colonial, Geneva
This one is a 1990s two-story colonial near Mill Creek. The kitchen as it was: white appliances and white thermofoil cabinets peeling at the edges, oak trim. What bothered the owners most: an old hood that was loud and pulled very little air. After: a new stainless chimney range hood ducted to the outside. The job covered removing the old hood, blocking and mounting, plus wall cap or roof jack.
Range Hood Installation in Geneva →
Before
AfterBefore and after: a 1980s two-story in Batavia
Cabinets in pale sage with unlacquered brass knobs and cup pulls, charcoal concrete-look quartz counters, a terracotta-look square tile backsplash, light oak hardwood flooring and black cage pendants and slim recessed lights.
Kitchen Remodeling in Batavia →
Before
AfterBefore and after: a two-story colonial from the 1990s in Batavia
Finished: the same doors sprayed in forest green, new satin brass pulls; counters and floor stayed as they were.
Kitchen Cabinet Painting in Batavia →From the old unit to the new one
- Photos and modelSend photos of the range wall, the old hood and the cabinet above, plus the model you like.
- Duct route and sizingWe decide where the duct can run and which hood fits that route.
- Written estimateA clear written price with duct and electrical work listed separately.
- Install and testHood mounted, ducted and wired, then every speed tested and the damper checked.
Range Hood Installation questions from Batavia homeowners
Can I install a range hood myself?
A simple swap on the same duct can be DIY. When the job involves a new duct route, a roof jack or a permit, it's worth hiring it out.
Do I need a permit to install a range hood?
Replacing a hood in place is usually simple; new ductwork and roof or wall holes are what bring permits into play.
How much does range hood installation cost?
A swap on an existing duct and a new island hood with a roof jack are very different jobs. You get a line-item estimate before work starts.
Can a range hood vent into the attic?
No. Kitchen exhaust has to go all the way outside through a wall cap or roof jack, never into an attic, soffit or joist space.
How many CFM does my range hood need?
There's no one answer. Gas, pro-style burners and heavy searing push it up; induction and light cooking need less.
What is the Batavia building department phone number?
Permits go through City of Batavia Community & Economic Development - Building Division, phone 630-454-2700. When your scope needs one, we prepare the application and schedule the inspections.
Do I need historic review for range hood installation in Batavia?
Batavia has locally reviewed areas, including Downtown Historic District and City Historic Preservation Commission reviews certificates of appropriateness. Exterior changes there can need review; interior-only work usually does not. We check before anything changes on the outside.
Who inspects kitchen hoods and fire safety in Batavia?
Batavia Fire Department, 800 E Wilson St. We schedule the inspection and have the paperwork ready.
Do I need a permit for range hood installation in Batavia?
It depends on the scope. Batavia's rule in short: Building permits are required for all construction; a Residential Alteration handout is available. We handle the permit when one is needed with City of Batavia Community & Economic Development - Building Division.
Do you work in my part of Batavia?
Yes. Our crews work across Batavia — ZIP 60510, 60539 — and nearby Geneva, St. Charles, West Chicago.
Working in Batavia
- A lot of Batavia kitchens date from the 1990s. We know these layouts well and what is worth keeping.
- Most Batavia homes are single-family. We protect floors and driveways and leave the site clean every day.
- Live in the Downtown Historic District? Interior kitchen work is usually not reviewed. We check before anything touches the exterior.
ZIP 60510ZIP 60539
Range Hood Installation nearby
Other kitchen services in Batavia
Range Hood RepairFans, motors, switches, lights and rattles on kitchen range hoods.
Oven, Range & Cooktop InstallationGas and electric ranges, wall ovens and cooktops, safely connected.
Kitchen Electrical WorkNew circuits and outlets for kitchen appliances.
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.