Scale on the aerator from lake water
White crust on the spray face is mineral buildup. Many Elmhurst owners just need the aerator cleaned or swapped, not a new faucet.
Serving Elmhurst & nearby Villa Park, Lombard
Kitchen Faucet Installation in Elmhurst, IL
Pull-down, touchless and two-handle kitchen faucets installed leak-free by licensed plumbers in Elmhurst.
- Serving Elmhurst ZIP 60126
- Installed level, sealed and tested before we leave
- Clear price for the install before the visit
Kitchen faucet problems we fix in Elmhurst
We install kitchen faucets in Elmhurst: the old one off, seized shut-off valves replaced when needed, the new faucet mounted to fit your sink holes and every supply connection checked under pressure.
Faucet leaking from the base
A puddle at the foot of the faucet each time you use it comes from the spout seals. We rebuild it if parts exist, or install a new one.
Hole count doesn't match the new faucet
A single-hole faucet on a three-hole sink needs a deck plate. A widespread faucet needs three holes, which we can drill in stone counters.
Shut-off valves that won't turn
Faucet swaps often stop at the valves: old multi-turn stops seize or leak when turned. We replace them with quarter-turn valves.
Spout too short or too low
A low spout makes it hard to fill stockpots and leaves water splashing at the back. A high-arc or pull-down faucet gives more room.
Faucet loose or wobbling on the sink
Wobbly faucets loosen further over time and start leaking at the deck. A proper re-mount fixes it.
Drip from the spout that won't stop
If the spout drips day and night, the seal inside the valve has worn. We repair it or put in a new faucet.
Pull-down sprayer that won't retract
A pull-down head that hangs instead of snapping back usually has a misplaced counterweight or a hose catching under the sink. We fix the routing.
What the install includes
- Clean the deckOld putty, caulk and mineral residue cleaned from the mounting surface.
- Replace valves when neededSeized or leaking stops replaced with quarter-turn valves.
- Mount the faucetFaucet set with its gasket or deck plate and tightened from below.
- Pull-down hose and weightSprayer hose connected and its counterweight placed correctly.
- Supply connectionsHot and cold lines hooked up to the valves.
- Power for touchless modelsSensor faucet wiring and power placed where it can be serviced.
- Flush and testWe run hot and cold, test the sprayer and look for drips below.
Models, parts and fittings
FinishesChrome wipes clean easily; matte and brushed finishes hide spots.
Filtered-water and pot-filler tapsExtra taps that use a spare hole or a separate supply line.
Pull-down faucetsHigh spout with a docking spray head for rinsing and filling pots.
Touchless and touch faucetsHands-free models for messy hands, with a control box below.
Bridge and two-handle faucetsSeparate hot and cold handles on a bridge or widespread base for traditional kitchens.
What the work looks like in Elmhurst homes
Before
Installed
DetailKitchen Faucet Installation in a two-story colonial from the 1990s, Elmhurst
A two-story colonial from the 1990s in Elmhurst, a typical kitchen for Elmhurst. Before: white double sink. What bothered the owners most: a leaking two-handle faucet with a side sprayer. After: a new single-handle pull-down faucet with a clean caulk line. The job covered replace valves when needed, pull-down hose and weight, plus supply connections.
Before
AfterLombard kitchen, 1980s condo: kitchen faucet installation
A 1980s condo in Lombard, a typical kitchen for Lombard. What we started with: stainless double sink. The reason for the call: a faucet too low to fill a stockpot. Finished kitchen: a new single-handle pull-down faucet with a clean caulk line. On site this meant mount the faucet, power for touchless models, plus flush and test.
Kitchen Faucet Installation in Lombard →
Before
AfterKitchen Faucet Installation in a 1980s two-story, Addison
A 1980s two-story in Addison, a typical kitchen for Addison. What we started with: white cast-iron double sink. The reason for the call: handles that leaked and a sprayer that dribbled. After: a new single-handle pull-down faucet with a clean caulk line. Work included clean the deck, power for touchless models, plus flush and test.
Kitchen Faucet Installation in Addison →
Before
AfterAn Elmhurst 1950s ranch: before and after
What changed: a new island with a prep sink, the drain, vent and water lines relocated from the old wall.
Kitchen Plumbing Relocation in Elmhurst →
Before
AfterBefore and after: a 1950s ranch in Elmhurst
Cabinets in light butter yellow with satin brass pulls, creamy quartzite-look quartz counters, a green zellige-look tile backsplash, warm oak luxury vinyl plank flooring and a flush drum fixture and under-cabinet lights.
Kitchen Remodeling in Elmhurst →Install day
- Pick a faucetChoose one yourself or ask us what fits your sink and holes.
- Check the setupA quick look under the sink tells us what else the job needs.
- Written estimateYou get the price in writing, including any valve replacement.
- Install and testThe faucet goes in, a licensed plumber connects it and we test every joint.
Kitchen Faucet Installation questions from Elmhurst homeowners
Why is my faucet leaking from the base?
Usually failed internal O-rings at the swivel. Less often, the mounting gasket.
Pull-down or pull-out: which should I choose?
If there's room above the sink, a pull-down. If space is tight, a pull-out.
Can you install a faucet I already bought?
Yes. We check that it fits your sink and supplies and install it.
Do I need a plumber to install a faucet?
We recommend it, especially when the shut-off valves are old or the faucet needs a new hole. A licensed plumber makes the connections on every faucet we install.
How long does it take to install a kitchen faucet?
A straightforward swap is usually done in a short visit; touchless models and valve replacement take a little longer.
Is Elmhurst water hard, and does it matter for faucet installation?
Elmhurst's water source: Lake Michigan water purchased from DuPage Water Commission (supplied by City of Chicago); standby wells are emergency backup; reported hardness is About 144 mg/L as CaCO3, roughly 8 grains per gallon. Aerators and cartridges scale faster with harder water.
What is the Elmhurst building department phone number?
Permits go through Community Development Department (Building), phone 630-530-3030. When your scope needs one, we prepare the application and schedule the inspections.
What is Elmhurst doing about lead water lines?
The City publishes lead service line information; water is purchased from the DuPage Water Commission, supplied from the City of Chicago. A filter certified for lead reduction is a sensible step until your line is confirmed or replaced.
Do I need a permit for faucet installation in Elmhurst?
It depends on the scope. Elmhurst's rule in short: Elmhurst requires permits for building and construction projects; all permits are applied for through the City's Citizen Self-Service Portal. We handle the permit when one is needed with Community Development Department (Building).
Do you work in my part of Elmhurst?
Yes. Our crews work across Elmhurst — ZIP 60126 — and nearby Villa Park, Lombard, Addison.
Working in Elmhurst
- A lot of Elmhurst kitchens date from the 1950s. We know these layouts well and what is worth keeping.
- Most Elmhurst homes are single-family. We protect floors and driveways and leave the site clean every day.
- We know how Community Development Department (Building) handles kitchen permits and pull them for you.
ZIP 60126
Kitchen Faucet Installation nearby
Other kitchen services in Elmhurst
Kitchen Sink Installation & ReplacementNew sinks, undermount and farmhouse styles.
Garbage Disposal Installation & RepairDisposals unjammed, repaired or replaced, with the drain connected right.
Kitchen Plumbing RelocationMove the sink to the island or another wall, drain and vent done right.
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.