Visible LED dots and glare under the cabinets
If your under-cabinet lights glare off the stone, we swap them for diffused LEDs and add a light rail where needed to hide them.
Serving Wood Dale & nearby Itasca, Elk Grove Village
Kitchen Lighting Installation in Wood Dale, IL
Recessed, pendant and under-cabinet lighting for Wood Dale kitchens, laid out so the counters are bright and wired by a licensed electrician.
- Serving Wood Dale ZIP 60191
- A new look without tearing the kitchen out
- Clean, protected work area every day
Kitchen lighting problems we solve in Wood Dale
Good kitchen light comes down to placement, color and control. We lay out the fixtures before cutting a single hole, pick a warm white that flatters the finishes, and wire everything to switches that make sense in your Wood Dale kitchen.
Light that looks too blue or too yellow
Color temperature sets the mood. Warm white around 2700 to 3000K is common in kitchens, while cooler light can make wood and stone look harsh.
Switches in the wrong place or one switch for everything
A switch on the far side of the room is a daily nuisance. We move or add controls where you walk in.
Canned or canless recessed lights?
Slim wafer fixtures need only a small hole and little room above. Housings with trims are better when you want to change trims later.
Recessed lights under an insulated attic
Non-IC cans need clearance from insulation. We install fixtures rated for contact so the attic stays fully insulated.
One old fixture lighting the whole kitchen
A single dome or flush fixture can't light a whole kitchen evenly. We replace it with a layout of recessed or surface LEDs across the ceiling.
Fluorescent box or panel that hums and flickers
Fluorescent tubes and ballasts wear out and are hard to dim. A switch to LED fixtures gives steadier light and dimming.
LEDs that flicker or buzz on the dimmer
Flickering LEDs are usually a dimmer mismatch. We replace the control with one rated for the fixtures on that switch.
What the work covers
- Lighting layoutA plan for ceiling, task, island and accent light, with fixture positions and switching.
- Wiring and circuit checkWe confirm the lighting circuit can carry the new fixtures.
- Old fixtures removedFluorescent boxes, old cans and outdated fixtures taken down and wiring made safe.
- Ceiling openings and boxesHoles cut for recessed lights and fixture boxes set and braced for pendants.
- Wire fished to fixtures and switchesNew cable run through the ceiling and walls with minimal access holes.
- Fixtures installedEach fixture hung, leveled and wired.
- Switches and dimmersControls installed where you enter and use the kitchen.
Materials and finishes
Accent lightingIn-cabinet lights for glass doors, toe-kick strips and lighting above the cabinets.
Pendants and linear fixturesSingle, paired or grouped pendants and long linear lights over islands and peninsulas.
Dimmers and controlsLED-rated dimmers, smart switches and motion or timer controls.
Color temperature optionsWarm white around 2700 to 3000K, and selectable-color fixtures where you're unsure.
Under-cabinet LEDHardwired strips, puck lights or light bars mounted under the wall cabinets.
Kitchen Lighting Installation before and after — Wood Dale homes
Before
AfterWood Dale kitchen, 1960s ranch: kitchen lighting installation
This one is a 1960s ranch in Wood Dale. The kitchen as it was: a dome ceiling light. The main complaint was a single old light that left the counters in shadow. Finished kitchen: a flush drum fixture and under-cabinet lights on separate switches. The job covered lighting layout, old fixtures removed, plus ceiling openings and boxes.
Before
AfterItasca kitchen, 1990s two-story colonial: kitchen lighting installation
This one is a 1990s two-story colonial near Walnut Street downtown. What we started with: a brass chandelier over the nook. The main complaint was one ceiling fixture lighting the whole room. The result: two glass pendants and recessed lights on separate switches. Work included ceiling openings and boxes, fixtures installed, plus switches and dimmers.
Kitchen Lighting Installation in Itasca →
Before
AfterAn Elmhurst 1950s ranch: before and after
This one is a 1950s ranch in Elmhurst. Before: a round fluorescent ceiling ring. What bothered the owners most: an old fluorescent box that flickered. After: black cage pendants and slim recessed lights on separate switches. The job covered lighting layout, old fixtures removed, plus switches and dimmers.
Kitchen Lighting Installation in Elmhurst →
Before
AfterKitchen Remodeling in a postwar Cape Cod, Wood Dale
What changed: cabinets in soft white with unlacquered brass knobs and cup pulls, warm walnut butcher block counters, a blue handmade-look tile backsplash, warm oak luxury vinyl plank flooring and recessed lights and under-cabinet LED strips.
Kitchen Remodeling in Wood Dale →
Before
AfterKitchen Cabinet Painting in a 1960s ranch, Wood Dale
The same doors sprayed in powder blue, new satin brass pulls; counters and floor stayed as they were.
Kitchen Cabinet Painting in Wood Dale →How the job goes
- Share photos and plansSend photos of the kitchen, the ceiling and any fixtures you've picked.
- Layout visitWe check the ceiling type, joists, insulation and wiring, and mark fixture positions.
- Written estimateAn itemized estimate listing fixtures, wiring, switches, patching and any permit.
- Install and testFixtures wired and mounted, dimmers set, ceiling patched and everything tested.
Kitchen Lighting Installation questions from Wood Dale homeowners
Do I need a permit for kitchen lighting?
Sometimes. We confirm the Wood Dale rules and handle the permit when it applies.
Hardwired or plug-in under-cabinet lights?
Both work. Hardwired needs an electrician; plug-in needs a free outlet near each run.
How high should pendants hang over an island?
We start in the usual 30 to 36 inch range and adjust before fixing the final drop.
Can recessed lights go into a plaster ceiling?
Yes. Plaster needs careful cutting and sometimes added support, and slim canless fixtures often fit best.
Do I need an electrician to install kitchen lighting?
For new fixtures, new switches or any added circuits, yes. Replacing a fixture on an existing box is simpler, but a licensed electrician makes sure the box and wiring are sound.
Wood Dale contractor registration: do kitchen contractors need it?
All contractors (general, HVAC, electrical, plumbing, roofing, etc.) must register with the City before a permit is issued. Requires Certificate of Insurance ($2,000,000 public liability) naming the City, state license/IDPH registration if applicable. We take care of that before work starts.
Does kitchen lighting project need a Wood Dale building permit, and who files it?
Permits go through Community Development Department (https://my.wooddale.com), phone 630-766-5133. When your scope needs one, we prepare the application and schedule the inspections.
What does Wood Dale ask for on electrical work?
Electrical contractors must register with the City (insurance certificate, fee/bond per fee schedule); city adopts the 2014 National Electrical Code with local amendments. New circuits and wiring are done by licensed electricians.
Do I need a permit for kitchen lighting project in Wood Dale?
It depends on the scope. Wood Dale's rule in short: A permit is required for any alteration or repair of a building. We handle the permit when one is needed with Community Development Department.
Do you work in my part of Wood Dale?
Yes. Our crews work across Wood Dale — ZIP 60191 — and nearby Itasca, Elk Grove Village, Addison.
Working in Wood Dale
- A lot of Wood Dale kitchens date from the 1960s. We know these layouts well and what is worth keeping.
- Most Wood Dale homes are single-family. We protect floors and driveways and leave the site clean every day.
- We know how Community Development Department handles kitchen permits and pull them for you.
ZIP 60191
Kitchen Lighting Installation nearby
Other kitchen services in Wood Dale
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.
Cabinet RefacingNew doors and fronts on your existing cabinet boxes.
Countertop Fabrication & InstallationQuartz, granite and butcher block, templated and installed.
Kitchen Backsplash InstallationTile backsplashes with clean lines and flush outlets.