Pendants over the island
Two or three pendants, or one long linear fixture, are common over an island. We place the boxes so the lights line up with the island, not the old ceiling layout.
Serving Roselle & nearby Bloomingdale, Hanover Park
Kitchen Lighting Installation in Roselle, IL
Recessed, pendant and under-cabinet lighting for Roselle kitchens, laid out so the counters are bright and wired by a licensed electrician.
- Serving Roselle ZIP 60172
- A new look without tearing the kitchen out
- Clean, protected work area every day
Kitchen lighting problems we solve in Roselle
Good kitchen light comes down to placement, color and control. We lay out the fixtures before cutting a single hole, pick a warm white that flatters the finishes, and wire everything to switches that make sense in your Roselle kitchen.
One old fixture lighting the whole kitchen
A single dome or flush fixture can't light a whole kitchen evenly. We replace it with a layout of recessed or surface LEDs across the ceiling.
LEDs that flicker or buzz on the dimmer
Flickering LEDs are usually a dimmer mismatch. We replace the control with one rated for the fixtures on that switch.
Adding recessed lights to an existing ceiling
We cut new recessed lights into a finished ceiling, fish the wire from the switch and keep patching to a minimum.
Switches in the wrong place or one switch for everything
When every light is on one switch, you can't set a softer evening light. We split the layers onto separate switches and dimmers.
Recessed lights under an insulated attic
Fixtures in a ceiling with insulation above must be IC-rated, meaning they can touch insulation safely. Airtight models also keep warm air from leaking into the attic.
Dark counters and shadows where you work
We fix shadowed counters by adding task light under the wall cabinets and placing ceiling fixtures toward the front of the counters instead of the room's center.
Visible LED dots and glare under the cabinets
If your under-cabinet lights glare off the stone, we swap them for diffused LEDs and add a light rail where needed to hide them.
What's included
- Lighting layoutA plan for ceiling, task, island and accent light, with fixture positions and switching.
- Wiring and circuit checkWe confirm the lighting circuit can carry the new fixtures.
- Old fixtures removedFluorescent boxes, old cans and outdated fixtures taken down and wiring made safe.
- Wire fished to fixtures and switchesWe pull wire from the switch to each fixture location.
- Switches and dimmersLED-compatible dimmers and separate switches for each lighting layer.
- Testing and adjustmentWe run each circuit and fine-tune before leaving.
- Patching and cleanupWe close up openings and clean the work area.
Finishes we offer
Accent lightingIn-cabinet lights for glass doors, toe-kick strips and lighting above the cabinets.
Recessed lightingDownlights set into the ceiling for even general light.
Surface and flush fixturesLow-profile LED discs and flush or semi-flush fixtures for shallow or concrete ceilings.
Pendants and linear fixturesHanging fixtures that light the island and set the style.
Color temperature optionsLEDs in a consistent, warm color with good rendering.
What the work looks like in Roselle homes
Before
AfterBefore and after: a 1970s split-level in Roselle
The site: a 1970s split-level in Roselle. The kitchen as it was: a hanging swag lamp. The main complaint was one ceiling fixture lighting the whole room. After: two glass pendants and recessed lights on separate switches. Work included wiring and circuit check, switches and dimmers, plus patching and cleanup.
Before
AfterA Bloomingdale two-story colonial from the 1990s: before and after
This one is a two-story colonial from the 1990s near Old Town Bloomingdale. Before: two hanging glass pendants. The main complaint was old lights that no longer matched the kitchen. The result: black cage pendants and slim recessed lights on separate switches. The job covered wiring and circuit check, old fixtures removed, plus switches and dimmers.
Kitchen Lighting Installation in Bloomingdale →
Before
AfterKitchen Lighting Installation in a 1980s two-story, Itasca
The site: a 1980s two-story near South Side. The kitchen as it was: a brass chandelier over the nook. What bothered the owners most: one ceiling fixture lighting the whole room. After: two glass pendants and recessed lights on separate switches. On site this meant wiring and circuit check, wire fished to fixtures and switches, plus switches and dimmers.
Kitchen Lighting Installation in Itasca →
Before
AfterA Roselle 1970s split-level: before and after
What changed: cabinets in light greige with brushed nickel bar pulls, light marble-look quartz counters, a terracotta-look square tile backsplash, black-and-white checkerboard tile flooring and two glass pendants and recessed lights.
Kitchen Remodeling in Roselle →
Before
AfterRoselle kitchen, 1970s split-level: kitchen cabinet painting
Finished: the same doors sprayed in deep navy, new satin brass pulls; counters and floor stayed as they were.
Kitchen Cabinet Painting in Roselle →Day by day
- Share photos and plansTell us what feels too dark and what lights you have in mind.
- Layout visitAn electrician looks at the space and plans the layers and switching.
- Written estimateA clear written price before any ceiling is cut.
- Install and testWe install, test each light and clean up.
Kitchen Lighting Installation questions from Roselle homeowners
Can recessed lights go into a plaster ceiling?
Yes, with the right tools and patience. Older plaster on lath is common in our area, and we work with it often.
How high should pendants hang over an island?
We start in the usual 30 to 36 inch range and adjust before fixing the final drop.
How far from the cabinets should recessed lights be?
Lights too close to the uppers wash the doors; too far back leave you in shadow. We place them over the front of the counter.
Hardwired or plug-in under-cabinet lights?
Both work. Hardwired needs an electrician; plug-in needs a free outlet near each run.
Do I need an electrician to install kitchen lighting?
For new fixtures, new switches or any added circuits, yes. Replacing a fixture on an existing box is simpler, but a licensed electrician makes sure the box and wiring are sound.
Does Roselle require a licensed electrician for kitchen lighting project?
Plumbing, electrical and roofing contractors must hold either a state or local license; general contractor and all subs must hold a Village license. New circuits and wiring are done by licensed electricians.
Do I need a Roselle-registered contractor for kitchen lighting project?
Contractors must register with the Village via Cloudpermit and be licensed: surety bond, certificate of insurance naming the Village, $75 fee. We take care of that before work starts.
Does kitchen lighting project need a Roselle building permit, and who files it?
Permits go through Development & Engineering Services (Building & Zoning), phone 630-671-2821. When your scope needs one, we prepare the application and schedule the inspections.
Do I need a permit for kitchen lighting project in Roselle?
It depends on the scope. Roselle's rule in short: Permit required for projects including bathroom and kitchen remodeling, electrical and plumbing work; also water heater, roof, HVAC. We handle the permit when one is needed with Development & Engineering Services (Building & Zoning).
Do you work in my part of Roselle?
Yes. Our crews work across Roselle — ZIP 60172 — and nearby Bloomingdale, Hanover Park, Schaumburg.
Working in Roselle
- A lot of Roselle kitchens date from the 1970s. We know these layouts well and what is worth keeping.
- Most Roselle homes are single-family. We protect floors and driveways and leave the site clean every day.
- We know how Development & Engineering Services (Building & Zoning) handles kitchen permits and pull them for you.
ZIP 60172
Kitchen Lighting Installation nearby
Other kitchen services in Roselle
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.
Cabinet RefacingNew doors and fronts on your existing cabinet boxes.
Countertop Fabrication & InstallationQuartz, granite and butcher block, templated and installed.
Kitchen Backsplash InstallationTile backsplashes with clean lines and flush outlets.