Aluminum branch wiring
Some homes built in the late 1960s and 1970s used aluminum branch wiring. Connections need devices and connectors rated for aluminum, and we check them when we open the boxes.
Serving Palatine & nearby Arlington Heights, Buffalo Grove
Kitchen Electrical Work in Palatine, IL
New circuits, GFCI outlets, island power and panel upgrades for Palatine kitchens, done by a licensed electrician and inspected when required.
- Installers working in Palatine ZIP 60067, 60074
- Hookups by licensed trades where the code calls for it
- Old unit hauled away on request
Kitchen electrical problems we fix in Palatine
Whether you're remodeling or just tired of extension cords, the kitchen wiring has to keep up with how you cook. We check the panel, map the circuits, then add outlets, dedicated lines and safety protection for your Palatine home, with an inspection when the work calls for one.
Condo kitchens with limited panel room
Condo electrical work usually needs the association's sign-off and a permit. We handle both and work within building hours.
Too few outlets along the counter
Older kitchens may have one or two receptacles for a whole run of counter. Today's code usually spaces them so no stretch of counter is far from an outlet, and we add boxes to match.
Remodel rough-in and inspection
Kitchen remodels usually need an electrical permit. We lay out the outlets, appliance circuits and lighting, pass rough inspection and complete the trim-out.
Two-prong outlets and no ground
Adapters on two-prong outlets don't add a ground. A licensed electrician either rewires the run or installs GFCI protection per code.
Switching to induction or adding a wall oven
A double wall oven or induction cooktop needs heavier wire and a larger breaker than an old outlet provides. We size and install both.
No GFCI protection at the counter
Outlets near the sink and along the counters should be GFCI protected, which cuts power fast if current leaks through water or a person. We add GFCI receptacles or breakers.
Flickering or dimming when appliances start
Lights that dim when the microwave kicks on can mean shared or overloaded circuits or a loose connection. We test and trace the cause.
Included with the install
- Plan and permitA layout of outlets, circuits and switches, with a permit pulled when new circuits are added.
- Panel workRoom made in the panel for the kitchen circuits.
- Small-appliance circuitsDedicated 20-amp circuits for the counter outlets, as today's code usually calls for.
- Appliance circuitsIndividual circuits for the appliances that need them, including 240-volt cooking circuits.
- GFCI and AFCI protectionGFCI on counter and sink-area outlets, AFCI where today's code usually requires it.
- InspectionWe meet the inspector and close out the permit.
- Patching and cleanupAccess holes closed up and the work area cleaned, with finish painting by arrangement.
What to pick before the install
20-amp counter circuitsHeavier wire and breakers for the outlets that power kettles, toasters and mixers.
240-volt appliance circuitsCircuits for ranges, wall ovens and induction cooktops, sized to the nameplate.
GFCI receptacles and breakersRequired at the counters and near water; available as outlets or breakers.
Pop-up, under-cabinet and USB outletsWays to add power without cluttering the backsplash.
AFCI and dual-function breakersBreakers that detect arcing in damaged wiring, often combined with GFCI.
Kitchens like yours in Palatine: before and after
Before
Installed
DetailKitchen Electrical Work in a 1990s two-story colonial, Palatine
This one is a 1990s two-story colonial in Palatine. What we started with: white ceramic tile with dark stained grout lines and white appliances. The main complaint was old two-prong outlets along the counter. Finished kitchen: new GFCI outlets at counter height on a dedicated circuit, cover plates installed. Work included panel work, small-appliance circuits, plus GFCI and AFCI protection.
Before
AfterBefore and after: a two-story colonial from the 1990s in Arlington Heights
This one is a two-story colonial from the 1990s in Arlington Heights. What we started with: white Corian-style solid surface with a yellowed seam and black appliances. What bothered the owners most: a kitchen circuit that kept tripping. After: new GFCI outlets at counter height on a dedicated circuit, cover plates installed. On site this meant panel work, GFCI and AFCI protection, plus inspection.
Kitchen Electrical Work in Arlington Heights →
Before
AfterBefore and after: a 1980s two-story in Hoffman Estates
This one is a 1980s two-story in Hoffman Estates. The kitchen as it was: almond laminate with a backsplash lip and almond appliances. The reason for the call: outlets that tripped whenever two appliances ran. The result: new GFCI outlets at counter height on a dedicated circuit, cover plates installed. On site this meant small-appliance circuits, appliance circuits, plus patching and cleanup.
Kitchen Electrical Work in Hoffman Estates →
Before
AfterPalatine kitchen, two-story colonial from the 1990s: kitchen remodeling
Finished: cabinets in white uppers and deep green lowers with polished nickel pulls, dark soapstone-look quartz counters, a white herringbone tile backsplash, warm oak luxury vinyl plank flooring and a flush drum fixture and under-cabinet lights.
Kitchen Remodeling in Palatine →
Before
AfterBefore and after: a 1990s two-story colonial in Palatine
The same doors sprayed in deep navy, new brushed nickel bar pulls; counters and floor stayed as they were.
Kitchen Cabinet Painting in Palatine →How the install goes
- Tell us what's going wrong or what you're planningDescribe the tripping, dead outlets or new appliances, and send photos of the panel.
- Site checkWe look at the wiring, panel capacity and outlet layout in person.
- Written estimateA clear written price before any work starts.
- Wiring and inspectionWe do the work, test every outlet and close out the permit.
Kitchen Electrical Work questions from Palatine homeowners
Do kitchen outlets have to be GFCI?
Yes for the counters and near the sink. It can be a GFCI outlet or a GFCI breaker protecting the whole circuit.
Should I replace old wiring in an older home?
We recommend it for the kitchen at least. Old insulation and no ground don't mix with heavy appliances.
Do I need outlets on my kitchen island?
Most owners want them for small appliances. We place side or pop-up outlets on a protected circuit.
How many circuits does a kitchen need?
Today's code usually calls for at least two 20-amp circuits for counter outlets, plus dedicated circuits for appliances like the dishwasher, disposal, microwave and range as the maker or code requires.
Does Palatine require a licensed electrician for kitchen circuits?
Electrical licensing in Illinois is handled town by town. We check what Palatine requires and pull the permit when new circuits are added.
Do Palatine condo associations need to approve kitchen electrical work?
Associations usually set rules for work hours, elevators, deliveries and insurance, and many require approval for plumbing, electrical or structural changes. We provide the certificate of insurance and follow the building's rules.
Do I need a Palatine-registered contractor for kitchen electrical work?
Contractors must be registered and bonded with the Village before a permit is issued. Registration is online and expires Dec 31 each year. We take care of that before work starts.
Does kitchen electrical work need a Palatine building permit, and who files it?
Permits go through Community Development Department - Building Permits & Inspections, phone (847) 359-9042. When your scope needs one, we prepare the application and schedule the inspections.
What does Palatine ask for on electrical work?
Electrical contractors must register with the Village, post a $10,000 surety bond and submit a copy of an accepted electrical license (Elgin, Libertyville, Schaumburg, Ottawa, Woodstock, Chicago, ICC Master Electrician; Orland Park supervisory certificate only). New circuits and wiring are done by licensed electricians.
Do I need a permit for kitchen electrical work in Palatine?
It depends on the scope. Palatine's rule in short: A permit is required to remodel a kitchen or to add/alter the electrical system. We handle the permit when one is needed with Community Development Department - Building Permits & Inspections.
Do you work in my part of Palatine?
Yes. Our crews work across Palatine — ZIP 60067, 60074 — and nearby Arlington Heights, Buffalo Grove, Lake Zurich.
Working in Palatine
- A lot of Palatine kitchens date from the 1970s. We know these layouts well and what is worth keeping.
- Condo or townhome? We follow association rules on work hours and elevators and bring the insurance certificate your board asks for.
- We know how Community Development Department - Building Permits & Inspections handles kitchen permits and pull them for you.
ZIP 60067ZIP 60074
Kitchen Electrical Work nearby
Other kitchen services in Palatine
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.
Cabinet RefacingNew doors and fronts on your existing cabinet boxes.
Countertop Fabrication & InstallationQuartz, granite and butcher block, templated and installed.
Kitchen Backsplash InstallationTile backsplashes with clean lines and flush outlets.