Venting rules in a Mount Prospect condo
Before we plan a duct in a condo unit, we look at the building's rules and what the existing vent connects to.
Serving Mount Prospect & nearby Des Plaines, Arlington Heights
Range Hood Installation in Mount Prospect, IL
We install under-cabinet, wall chimney, island and insert range hoods in Mount Prospect, ducted outside wherever the house allows.
- Serving Mount Prospect ZIP 60056, 60005
- Installed level, sealed and tested before we leave
- Clear price for the install before the visit
Range hood installs we handle in Mount Prospect
A range hood only works as well as the duct behind it. In Mount Prospect we size the hood to your cooktop, plan the shortest smooth duct path to an outside wall or the roof, mount the hood at the height its maker calls for and test the airflow before we leave.
1960s hood on an old duct
Original 1960s ventilation was sized for a different era of cooking. A modern hood often needs a larger duct and a new exterior cap.
Old hood that only recirculates
A hood that blows air back into the room through a charcoal filter catches some grease but leaves heat, moisture and smoke inside. When a duct route exists, we convert it to vent outdoors.
High-CFM hood and makeup air
Bigger isn't always better. Above a certain airflow, many codes call for makeup air, so we size the hood to what you actually cook.
Custom hood cover that needs an insert
Wood or plaster hood covers need a liner or insert inside them. We install the insert, the duct and the wiring so the cover can be finished around it.
Swapping an over-the-range microwave for a hood
Many owners trade the microwave above the range for a proper hood. The cabinet above may need trimming and the duct usually needs upgrading.
Long duct run with many elbows
Every elbow and every foot of duct cuts airflow. We plan the most direct route to the outside and use as few turns as the framing allows.
Gas range that needs stronger ventilation
Cooking on gas puts more into the kitchen air than electric or induction does. A ducted hood with enough capture area and airflow is the right match.
Included with the install
- Site check and sizingCooktop width, fuel type and duct path are checked before a model is chosen.
- Blocking and mountingMounting points set at the height in the maker's instructions.
- Duct runRigid smooth metal duct sized to the hood outlet, joints sealed with foil tape and supported.
- Wall cap or roof jackThe duct ends outside under a damper that closes when the fan is off.
- Electrical connectionPower brought to the hood and connected per the maker's instructions.
- Recirculating setupDuctless installs get the maker's charcoal filter kit and a clear plan for replacing it.
- Test and cleanupWe run the hood, confirm the damper opens and closes, and haul away the old unit.
Models, parts and fittings
Duct, caps and dampersRigid galvanized or stainless duct, wall caps and roof jacks with backdraft dampers.
Under-cabinet hoodsThe most common style, tucked under the upper cabinet above the range.
Island hoodsCeiling-hung hoods for cooktops in an island, usually wider than the cooking surface.
Internal and remote blowersMost hoods carry the fan inside; some use an inline or exterior blower to cut noise in the kitchen.
Wall chimney hoodsA canopy on the wall with a chimney cover hiding the duct up to the ceiling.
Kitchens like yours in Mount Prospect: before and after
Before
Installed
DetailRange Hood Installation in a suburban townhome, Mount Prospect
A suburban townhome in Mount Prospect, a typical kitchen for Mount Prospect. The kitchen as it was: white appliances and oak flat-panel cabinets. The main complaint was an old hood that was loud and pulled very little air. The result: a new stainless chimney range hood ducted to the outside. The job covered site check and sizing, electrical connection, plus recirculating setup.
Before
AfterDes Plaines kitchen, 1980s two-story: range hood installation
The site: a 1980s two-story in Des Plaines. What we started with: almond appliances and honey-oak cathedral raised-panel cabinets with worn finish near the handles, brass knobs. The main complaint was an old hood that was loud and barely pulled any air. The result: a new stainless chimney range hood ducted to the outside. On site this meant blocking and mounting, wall cap or roof jack, plus electrical connection.
Range Hood Installation in Des Plaines →
Before
AfterBefore and after: a two-story colonial from the 1990s in Arlington Heights
A two-story colonial from the 1990s in Arlington Heights, a typical kitchen for Arlington Heights. The kitchen as it was: white appliances and white thermofoil cabinets peeling at the edges, oak trim. What bothered the owners most: cooking smells that stayed in the house for hours. The result: a new stainless chimney range hood ducted to the outside. Work included blocking and mounting, recirculating setup, plus test and cleanup.
Range Hood Installation in Arlington Heights →
Before
AfterMount Prospect kitchen, postwar Cape Cod: kitchen remodeling
What changed: cabinets in white uppers and dusty blue lowers with matte black pulls, bright white quartz counters, a terracotta-look square tile backsplash, black-and-white checkerboard tile flooring and recessed lights and under-cabinet LED strips.
Kitchen Remodeling in Mount Prospect →
Before
AfterA Mount Prospect postwar bi-level: before and after
The same doors sprayed in pale sage, new polished nickel pulls; counters and floor stayed as they were.
Kitchen Cabinet Painting in Mount Prospect →How the install goes
- Photos and modelSend photos of the range wall, the old hood and the cabinet above, plus the model you like.
- Duct route and sizingWe decide where the duct can run and which hood fits that route.
- Written estimateA clear written price with duct and electrical work listed separately.
- Install and testWe install, test the airflow and clean up the same day in most cases.
Range Hood Installation questions from Mount Prospect homeowners
Can I duct a hood outside in my Mount Prospect condo?
Many condo boards must approve any exterior penetration. If it's not allowed, a recirculating hood is the option.
Do I need an electrician to install a range hood?
If power is already at the hood location, no. If it isn't, an electrician adds it before we hang the hood.
What size range hood do I need?
Start with width: match or exceed the cooking surface. Then pick a fan sized for what you cook and the duct you can run.
Who installs a range hood: a plumber, an electrician or a contractor?
It's mostly a ventilation and carpentry job with an electrical connection. We do the mounting and ducting and bring in an electrician when new wiring is needed.
How high should a range hood be above the stove?
Every hood has a mounting height in its installation guide. Too high and it misses smoke; too low and it gets in the way.
Do Mount Prospect condo associations need to approve range hood installation?
Associations usually set rules for work hours, elevators, deliveries and insurance, and many require approval for plumbing, electrical or structural changes. We provide the certificate of insurance and follow the building's rules.
Do I need a Mount Prospect-registered contractor for range hood installation?
A Contractor's License is required for general contractors (and listed trades); $200, valid one year, applied for through the online portal. We take care of that before work starts.
What is the Mount Prospect building department phone number?
Permits go through Community Development Department - Building & Inspection Services, phone (847) 870-5675. When your scope needs one, we prepare the application and schedule the inspections.
Which Mount Prospect office signs off on hood work?
Fire Prevention Bureau / Fire Marshal. We schedule the inspection and have the paperwork ready.
What does Mount Prospect ask for on electrical work?
Electrical contractors need the Village contractor license and must submit their state license/registration. A licensed electrician is required in multi-family buildings (condos, townhomes, 3-flats). New circuits and wiring are done by licensed electricians.
Do I need a permit for range hood installation in Mount Prospect?
It depends on the scope. Mount Prospect's rule in short: Kitchen remodels need a permit and a code review (about 10 business days). We handle the permit when one is needed with Community Development Department - Building & Inspection Services.
Do you work in my part of Mount Prospect?
Yes. Our crews work across Mount Prospect — ZIP 60056, 60005 — and nearby Des Plaines, Arlington Heights, Elk Grove Village.
Working in Mount Prospect
- A lot of Mount Prospect kitchens date from the 1960s. We know these layouts well and what is worth keeping.
- Condo or townhome? We follow association rules on work hours and elevators and bring the insurance certificate your board asks for.
- We know how Community Development Department - Building & Inspection Services handles kitchen permits and pull them for you.
ZIP 60056ZIP 60005
Range Hood Installation nearby
Other kitchen services in Mount Prospect
Range Hood RepairFans, motors, switches, lights and rattles on kitchen range hoods.
Oven, Range & Cooktop InstallationGas and electric ranges, wall ovens and cooktops, safely connected.
Kitchen Electrical WorkNew circuits and outlets for kitchen appliances.
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.