Aluminum branch wiring
Some homes built in the late 1960s and 1970s used aluminum branch wiring. Connections need devices and connectors rated for aluminum, and we check them when we open the boxes.
Serving Lombard & nearby Villa Park, Glen Ellyn
Kitchen Electrical Work in Lombard, IL
New circuits, GFCI outlets, island power and panel upgrades for Lombard kitchens, done by a licensed electrician and inspected when required.
- Serving Lombard ZIP 60148
- Installed level, sealed and tested before we leave
- Clear price for the install before the visit
Kitchen electrical problems we fix in Lombard
Breakers that trip at breakfast, too few outlets along the counter, a new induction range with nowhere to plug in: these are the calls we get from Lombard kitchens. A licensed electrician finds the cause, explains the fix and does the wiring to today's code.
Condo kitchens with limited panel room
Condo electrical work usually needs the association's sign-off and a permit. We handle both and work within building hours.
New appliance needs its own circuit
Dishwashers, disposals, built-in microwaves and refrigerators often need dedicated circuits per the maker or code. We run them from the panel before install day.
Switching to induction or adding a wall oven
Induction ranges, cooktops and electric wall ovens run on 240-volt circuits sized to their nameplate. We check panel capacity and run the circuit.
No GFCI protection at the counter
Today's code usually requires GFCI protection for counter receptacles and, in newer editions, most kitchen outlets. We bring yours up to it.
Two-prong outlets and no ground
Ungrounded receptacles can't safely power modern appliances with three-prong plugs. We replace the wiring or add protection as the situation allows.
Under-cabinet outlets and power for an appliance garage
Hiding outlets under the wall cabinets is a common request with a new backsplash. We plan it before the tile goes up.
Flickering or dimming when appliances start
If the lights pulse every time the fridge compressor starts, we look at what that circuit carries and how it's connected.
Included with the install
- Circuit mapping and panel checkEvery breaker serving the kitchen is traced and the panel load is reviewed.
- Plan and permitA layout of outlets, circuits and switches, with a permit pulled when new circuits are added.
- Small-appliance circuitsCounter receptacles split across separate circuits.
- Appliance circuitsDedicated lines for the dishwasher, disposal, microwave, refrigerator and range or oven per the maker or code.
- Outlets and boxesOutlets added and placed where the counter is actually used.
- InspectionRough and final inspections scheduled with the village when a permit is involved.
- Patching and cleanupAccess holes closed up and the work area cleaned, with finish painting by arrangement.
What to pick before the install
240-volt appliance circuitsCircuits for ranges, wall ovens and induction cooktops, sized to the nameplate.
20-amp counter circuitsHeavier wire and breakers for the outlets that power kettles, toasters and mixers.
GFCI receptacles and breakersProtection that shuts power off in a fraction of a second when current leaks to ground.
Cable and conduitCopper wiring in cable or metal conduit, depending on what your village requires.
Pop-up, under-cabinet and USB outletsOutlets that hide in the island top, run under the uppers or include USB charging.
Kitchen Electrical Work before and after — Lombard homes
Before
Installed
DetailA Lombard 1990s two-story colonial: before and after
The site: a 1990s two-story colonial in Lombard. What we started with: white ceramic tile with dark stained grout lines and white appliances. The reason for the call: old two-prong outlets along the counter. After: new GFCI outlets at counter height on a dedicated circuit, cover plates installed. Work included small-appliance circuits, outlets and boxes, plus patching and cleanup.
Before
AfterA Villa Park 1980s two-story: before and after
A 1980s two-story in Villa Park, a typical kitchen for Villa Park. The kitchen as it was: white Corian-style solid surface with a yellowed seam and black appliances. The main complaint was too few outlets and an extension cord to the microwave. The result: new GFCI outlets at counter height on a dedicated circuit, cover plates installed. The job covered circuit mapping and panel check, small-appliance circuits, plus inspection.
Kitchen Electrical Work in Villa Park →
Before
AfterGlen Ellyn kitchen, 1990s two-story colonial: kitchen electrical work
This one is a 1990s two-story colonial in Glen Ellyn. The kitchen as it was: almond laminate with a backsplash lip and almond appliances. What bothered the owners most: outlets that tripped whenever two appliances ran. After: new GFCI outlets at counter height on a dedicated circuit, cover plates installed. The job covered plan and permit, inspection, plus patching and cleanup.
Kitchen Electrical Work in Glen Ellyn →
Before
AfterBefore and after: a 1950s ranch in Lombard
Cabinets in dark teal with brushed nickel bar pulls, charcoal concrete-look quartz counters, a white 2x8 tile in a vertical stack backsplash, hickory luxury vinyl plank flooring and recessed lights and under-cabinet LED strips.
Kitchen Remodeling in Lombard →
Before
AfterLombard kitchen, postwar Cape Cod: kitchen cabinet painting
What changed: the same doors sprayed in powder blue, new satin brass pulls; counters and floor stayed as they were.
Kitchen Cabinet Painting in Lombard →From the old unit to the new one
- Tell us what's going wrong or what you're planningDescribe the tripping, dead outlets or new appliances, and send photos of the panel.
- Site checkWe look at the wiring, panel capacity and outlet layout in person.
- Written estimateAn itemized estimate listing each circuit, outlet, panel change and permit.
- Wiring and inspectionCircuits installed, devices tested and inspection passed when a permit is required.
Kitchen Electrical Work questions from Lombard homeowners
Is my panel big enough for a kitchen remodel?
We do a load calculation based on your appliances and the rest of the house. Many panels have room; some need a subpanel or upgrade.
Do I need a permit for kitchen electrical work?
Usually when new circuits are added or a panel is changed. Swapping a like-for-like outlet or switch often doesn't. We confirm with the village before starting.
How much does kitchen electrical work cost?
It depends on the number of circuits, panel capacity, wall access and permit requirements. We give a written, itemized estimate after the site check.
Do you also install kitchen lighting?
Yes. Recessed, pendant and under-cabinet lighting have their own service page, and we often do them with the circuit work.
How many circuits does a kitchen need?
It depends on your appliances. We count what you have and plan circuits so nothing shares more than it should.
Can you do kitchen electrical work in a Lombard condo?
Associations usually set rules for work hours, elevators, deliveries and insurance, and many require approval for plumbing, electrical or structural changes. We provide the certificate of insurance and follow the building's rules.
Do I need a Lombard-registered contractor for kitchen electrical work?
Contractors must register with the Village: $100 fee, valid 1 year, online or via Building Division; insurance certificate with at least $300,000 liability coverage. We take care of that before work starts.
Lombard building permit for kitchen electrical work: where do I apply?
Permits go through Building Division, Community Development and Building, phone (630) 620-5750. When your scope needs one, we prepare the application and schedule the inspections.
What does Lombard ask for on electrical work?
Registration requires a copy of a current electrician license from a testing municipality plus a certificate of insurance. New circuits and wiring are done by licensed electricians.
Do I need a permit for kitchen electrical work in Lombard?
It depends on the scope. Lombard's rule in short: Village requires a building permit for new structures and updates to existing structures; replacing interior doors and fixtures at the same size with no structural change needs no permit. We handle the permit when one is needed with Building Division, Community Development and Building.
Do you work in my part of Lombard?
Yes. Our crews work across Lombard — ZIP 60148 — and nearby Villa Park, Glen Ellyn, Addison.
Working in Lombard
- A lot of Lombard kitchens date from the 1960s. We know these layouts well and what is worth keeping.
- Condo or townhome? We follow association rules on work hours and elevators and bring the insurance certificate your board asks for.
- We know how Building Division, Community Development and Building handles kitchen permits and pull them for you.
ZIP 60148
Kitchen Electrical Work nearby
Other kitchen services in Lombard
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.
Cabinet RefacingNew doors and fronts on your existing cabinet boxes.
Countertop Fabrication & InstallationQuartz, granite and butcher block, templated and installed.
Kitchen Backsplash InstallationTile backsplashes with clean lines and flush outlets.