Sewer or rotten-egg smell in the kitchen
Grease and food solids left too long in a trap turn rancid. Regular cleaning and a tight, gasketed lid usually end the odor.
Serving Glenview & nearby Northbrook, Park Ridge
Grease Trap Installation & Cleaning in Glenview, IL
Grease traps and interceptors sized, installed, cleaned and kept on schedule for restaurants and food-service kitchens in Glenview.
- Serving restaurants and kitchens in Glenview ZIP 60025, 60026, 60062
- Work scheduled around service hours
- Paperwork ready for inspectors
Grease trap problems we handle in Glenview
A grease trap only works when it is the right size and emptied before it fills. We install under-sink traps and in-ground interceptors for Glenview restaurants, cafes, bakeries and institutional kitchens, and set up cleaning so backups and FOG violations stop being a surprise.
Damaged lid, baffles or rusted trap
Steel traps rust out over the years and in-ground interceptors can crack. We inspect the inside during cleaning and tell you what has failed.
Interceptor overdue for pumping
An overdue interceptor is the start of most grease backups. We get it pumped, inspected and back on a schedule.
Grease clogs in the sewer line
Repeated main line clogs behind a restaurant usually trace back to a trap that's undersized, overdue or bypassed. We clear the line and correct the cause.
School, church or daycare kitchen trap
Community and school kitchens are often missed until a backup. A regular visit with records keeps them off the problem list.
Notice from the village or sanitary district
FOG programs can issue notices when grease shows up in the sewer downstream of your building. We inspect the trap, clean it and set up a maintenance schedule with records.
Health inspector asked about the grease trap
Inspectors want to see maintenance, not just a trap. Our service tickets and log give you the paper trail.
Not sure how often to clean
Frequency depends on trap size, menu and volume. We measure grease and solids at each visit and adjust the interval to what we find.
What the job covers
- Site visit and trap locationWe find the trap or interceptor, open it and look at size, condition and connections.
- SizingWe calculate the size from your sinks, flow and menu, not a guess.
- Permits and plan reviewPlumbing permit and plan review for new or replaced traps, where the village requires it.
- InstallationUnder-sink traps set and plumbed, or in-ground interceptors excavated, set and connected.
- Cleaning and pump-outSmall traps cleaned on site; larger interceptors pumped by licensed waste haulers.
- Inspection of baffles and outletWith the trap empty we check baffles, walls, lid gasket and the outlet line.
- Recurring scheduleA standing cleaning interval matched to your trap and cooking volume.
What goes into the system
Under-sink trap or interceptorIndoor traps suit lighter grease loads; interceptors suit busy kitchens and many fixtures.
Poly and coated steel trapsPolyethylene traps don't rust; coated steel is common in older installs.
Flow control fittingsA fitting that limits flow so the trap can do its job.
In-ground grease interceptorsLarge outdoor or below-slab tanks that hold more grease and are pumped less often.
Under-sink grease trapsCompact hydromechanical traps that sit under or next to a sink and are cleaned often.
Grease Trap Installation & Cleaning before and after — Glenview homes
Before
AfterGlenview kitchen, restaurant kitchen: grease trap installation & cleaning
This one is a restaurant kitchen near The Glen. The reason for the call: a grease trap that kept backing up the prep sinks. Finished kitchen: the same interceptor pumped and the lid closed, service hose coiled on the truck. Work included site visit and trap location, permits and plan review, plus recurring schedule.
Before
AfterNorthbrook kitchen, bakery kitchen: grease trap installation & cleaning
The site: a bakery kitchen near Downtown Northbrook. The reason for the call: a grease trap that kept backing up the prep sinks. The result: the same interceptor pumped and the lid closed, service hose coiled on the truck. The job covered sizing, permits and plan review, plus cleaning and pump-out.
Grease Trap Installation & Cleaning in Northbrook →
Before
AfterCommercial Hood Cleaning in a restaurant kitchen, Glenview
Finished: the same hood degreased to bare stainless with an inspection sticker area.
Commercial Hood Cleaning in Glenview →
Before
AfterA Glenview postwar Cape Cod: before and after
Finished: cabinets in white uppers and dusty blue lowers with matte black pulls, bright white quartz counters, a terracotta-look square tile backsplash, black-and-white checkerboard tile flooring and recessed lights and under-cabinet LED strips.
Kitchen Remodeling in Glenview →
Before
AfterBefore and after: a 1960s ranch in Glenview
The same doors sprayed in pale sage, new polished nickel pulls; counters and floor stayed as they were.
Kitchen Cabinet Painting in Glenview →From survey to sign-off
- Call or book a visitShare what you're seeing and any letter from the village or inspector.
- Inspect the trapWe open the trap, measure grease and solids and check its size and condition.
- Written estimateA clear written quote for the work and the recommended schedule.
- Clean, pump or installWe do the work around your hours and leave the area clean.
- Log and scheduleRecords for your files and a cleaning interval that fits your kitchen.
Grease Trap Installation & Cleaning questions from Glenview businesses
How often should a grease trap be cleaned?
There's no single answer. We measure at each visit and adjust, within whatever schedule your FOG authority requires.
Do I need a permit to install a grease trap?
Usually yes for a new or replacement trap or interceptor; it's plumbing work and often part of plan review for food establishments.
What can't go down a grease trap?
Don't pour used cooking oil down the sink; scrape plates before washing and keep food solids out of the drain.
Can you service the trap outside our hours?
Off-hours service is common for us, so the trap is handled without stopping the line.
How is a grease trap sized?
By the fixtures that drain into it and their flow rate, plus local rules. Interceptors are also sized by meals served and kitchen volume.
Glenview contractor registration: do kitchen contractors need it?
General and demolition contractors register with the Village: $50 fee, $25,000 bond, certificate of insurance and workers comp proof. Unlisted contractor types need no registration. We take care of that before work starts.
Does grease trap service need a Glenview building permit, and who files it?
Permits go through Community Development, Inspectional Services Division (Development Center), phone (847) 904-4330. When your scope needs one, we prepare the application and schedule the inspections.
Do you work in my part of Glenview?
Yes. Our crews work across Glenview, including The Park, The Glen, The Grove — ZIP 60025, 60026, 60062 — and nearby Northbrook, Park Ridge, Des Plaines.
Working in Glenview
- We plan Glenview jobs around your service hours, including early mornings, nights and closed days.
- We coordinate with Community Development, Inspectional Services Division (Development Center) and the fire department so inspections don't hold up your opening.
- We handle the paperwork landlords and property managers ask for: insurance, access times and scope sign-off.
The ParkThe GlenThe Grove
ZIP 60025ZIP 60026ZIP 60062
Grease Trap Installation & Cleaning nearby
Other kitchen services in Glenview
Commercial Kitchen Hood InstallationType I and II hoods, grease duct, fans and makeup air, built to NFPA 96.
Commercial Hood CleaningHood, duct and roof fan degreased to bare metal, after hours.
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.
Cabinet RefacingNew doors and fronts on your existing cabinet boxes.