Canned or canless recessed lights?
Slim wafer fixtures need only a small hole and little room above. Housings with trims are better when you want to change trims later.
Serving Skokie & nearby Evanston, Park Ridge
Kitchen Lighting Installation in Skokie, IL
Recessed, pendant and under-cabinet lighting for Skokie kitchens, laid out so the counters are bright and wired by a licensed electrician.
- Crews working in Skokie ZIP 60076, 60077, 60203
- Most jobs done in days, with your kitchen still usable
- Samples and a written quote before we start
Kitchen lighting problems we solve in Skokie
Most kitchens have enough light in the middle of the floor and too little where you actually chop and read recipes. In Skokie we plan lighting in layers: recessed or ceiling light for the room, under-cabinet strips for the counters, pendants over the island, each on its own switch or dimmer.
One old fixture lighting the whole kitchen
A single dome or flush fixture can't light a whole kitchen evenly. We replace it with a layout of recessed or surface LEDs across the ceiling.
Recessed lights under an insulated attic
Non-IC cans need clearance from insulation. We install fixtures rated for contact so the attic stays fully insulated.
Dark counters and shadows where you work
If the counters look dim even with every switch on, the light is in the wrong place, not too weak. We move it over the work zones.
Adding recessed lights to an existing ceiling
Adding can lights to a finished kitchen is mostly careful cutting and fishing wire. We plan the grid around joists, ducts and plumbing above.
Visible LED dots and glare under the cabinets
If your under-cabinet lights glare off the stone, we swap them for diffused LEDs and add a light rail where needed to hide them.
Switches in the wrong place or one switch for everything
When every light is on one switch, you can't set a softer evening light. We split the layers onto separate switches and dimmers.
LEDs that flicker or buzz on the dimmer
If the lights hum or pulse when dimmed, the dimmer and the driver don't agree. We pair them properly.
What we do on the job
- Lighting layoutWe mark where each light goes and which switch controls it.
- Old fixtures removedFluorescent boxes, old cans and outdated fixtures taken down and wiring made safe.
- Ceiling openings and boxesHoles cut for recessed lights and fixture boxes set and braced for pendants.
- Fixtures installedRecessed, pendant, surface and under-cabinet lights mounted and connected.
- Switches and dimmersLED-compatible dimmers and separate switches for each lighting layer.
- Testing and adjustmentWe run each circuit and fine-tune before leaving.
- Patching and cleanupAccess holes patched and the kitchen cleaned of dust.
Finishes we offer
Recessed lightingDownlights set into the ceiling for even general light.
Pendants and linear fixturesHanging fixtures that light the island and set the style.
Surface and flush fixturesCeiling-mounted lights when recessing isn't possible.
Accent lightingSofter layers that add depth in the evening.
Dimmers and controlsLED-rated dimmers, smart switches and motion or timer controls.
Kitchens like yours in Skokie: before and after
Before
AfterBefore and after: a 1950s ranch in Skokie
A 1950s ranch in Skokie, a typical kitchen for Skokie. Before: a fluorescent box light. The main complaint was a humming fluorescent light that left the counters flat and dim. Finished kitchen: two glass pendants and recessed lights on separate switches. On site this meant lighting layout, switches and dimmers, plus patching and cleanup.
Before
AfterKitchen Lighting Installation in a prewar brick bungalow, Evanston
The site: a prewar brick bungalow in Evanston. What we started with: a single pendant bowl light. What bothered the owners most: one ceiling fixture lighting the whole room. After: a flush drum fixture and under-cabinet lights on separate switches. The job covered old fixtures removed, ceiling openings and boxes, plus testing and adjustment.
Kitchen Lighting Installation in Evanston →
Before
AfterPark Ridge kitchen, 1950s ranch: kitchen lighting installation
The site: a 1950s ranch in Park Ridge. What we started with: a round fluorescent ceiling ring. The main complaint was a humming fluorescent light that left the counters flat and dim. The result: black cage pendants and slim recessed lights on separate switches. On site this meant lighting layout, old fixtures removed, plus patching and cleanup.
Kitchen Lighting Installation in Park Ridge →
Before
AfterKitchen Remodeling in a 1960s ranch, Skokie
Finished: cabinets in light butter yellow with polished nickel pulls, black honed granite counters, a gray beveled subway tile backsplash, light oak hardwood flooring and two glass pendants and recessed lights.
Kitchen Remodeling in Skokie →
Before
AfterBefore and after: a postwar bi-level in Skokie
The same doors sprayed in powder blue, new satin brass pulls; counters and floor stayed as they were.
Kitchen Cabinet Painting in Skokie →Day by day
- Share photos and plansSend photos of the kitchen, the ceiling and any fixtures you've picked.
- Layout visitAn electrician looks at the space and plans the layers and switching.
- Written estimateA clear written price before any ceiling is cut.
- Install and testWe install, test each light and clean up.
Kitchen Lighting Installation questions from Skokie homeowners
What color temperature is best for a kitchen?
Around 2700 to 3000K for a warm, natural look. Selectable-color fixtures let you decide after install.
Do I need an electrician to install kitchen lighting?
Anything beyond a bulb swap is best left to a licensed electrician. We also check whether the work needs a village permit.
How high should pendants hang over an island?
The bottom of the fixture usually sits around 30 to 36 inches above the counter, adjusted to your height and sight lines.
How much does kitchen lighting installation cost?
Fixture count, wiring access, patching and controls drive the price. We put it in writing before we start.
Can old recessed cans be switched to LED?
Often yes, with LED retrofit trims that screw into the old socket. If the housings are damaged or not rated for insulation, we replace them.
What is the Skokie building department phone number?
Permits go through Community Development Department - Building & Inspection Services Division (www.skokiepermits.com), phone (847) 933-8223. When your scope needs one, we prepare the application and schedule the inspections.
Skokie contractor registration: do kitchen contractors need it?
Many contractors must be registered and insured with the Village each year; permits are not issued unless all listed contractors are registered and insured. We take care of that before work starts.
Do I need a permit for kitchen lighting project in Skokie?
It depends on the scope. Skokie's rule in short: Electrical work and plumbing or electrical system changes need a permit. We handle the permit when one is needed with Community Development Department - Building & Inspection Services Division.
Do you work in my part of Skokie?
Yes. Our crews work across Skokie — ZIP 60076, 60077, 60203 — and nearby Evanston, Park Ridge, Glenview.
Working in Skokie
- A lot of Skokie kitchens date from the 1950s. We know these layouts well and what is worth keeping.
- Most Skokie homes are single-family. We protect floors and driveways and leave the site clean every day.
- We know how Community Development Department - Building & Inspection Services Division handles kitchen permits and pull them for you.
ZIP 60076ZIP 60077ZIP 60203
Kitchen Lighting Installation nearby
Other kitchen services in Skokie
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.
Cabinet RefacingNew doors and fronts on your existing cabinet boxes.
Countertop Fabrication & InstallationQuartz, granite and butcher block, templated and installed.
Kitchen Backsplash InstallationTile backsplashes with clean lines and flush outlets.