Fan won't turn off
A fan that keeps running after you switch it off usually has a stuck switch or a failed control relay. We replace the faulty part.
Serving Glenview & nearby Northbrook, Park Ridge
Range Hood Repair in Glenview, IL
Fan dead, lights out or a hood that rattles and roars? We repair range hoods in Glenview and tell you plainly when replacing makes more sense.
- Technicians covering Glenview ZIP 60025, 60026, 60062
- Diagnosis first, then a written price for the repair
- Honest advice when replacing makes more sense
Range hood problems we fix in Glenview
A hood that hums but won't spin, a light that stays dark, a fan stuck on one speed or a rattle that gets louder every week: these are everyday repairs. Our Glenview technicians diagnose the hood in place and fix it without tearing out cabinets.
Fan stuck on one speed
Losing speeds points to the speed control rather than the motor in most cases. We test the switch and the board.
Light not working but the fan is
When the fan runs but the lamp won't, the fix is often a new bulb, socket or LED module matched to the hood.
Backdraft damper stuck open or shut
A damper stuck shut chokes the fan; one stuck open lets cold air and noise in from outside. We free, clean or replace the damper.
Fan and light both dead
If nothing on the hood responds, we start with the power supply: the breaker, the wiring connection in the hood and the main control board.
Buttons or touch panel not responding
Touch controls fail from heat, grease and moisture getting into the panel. We test the keypad and the board and replace the faulty one.
Dripping grease or water from the hood
Grease dripping from the hood usually means saturated filters or a grease-filled duct. Water usually means condensation or a leak at the exterior cap.
Fan not working but the light is
Working lights mean the hood has power. A dead fan then points to the switch, the control board, a thermal cutoff or a failed motor.
What the repair visit covers
- DiagnosisWe test power, switches, controls, motor and lights to find the failed part.
- Fan motor replacementA new motor fitted, wired and balanced on its mount.
- Blower wheel serviceGrease-packed or loose blower wheels cleaned, tightened or replaced.
- Switches and control boardsFaulty controls swapped so every speed and setting responds again.
- Lights and socketsBulbs, sockets, LED modules and light switches replaced to match the hood.
- Filter replacementNew grease or charcoal filters fitted when the old ones are worn out.
- Noise and vibration fixesLoose mounts, filters, wheels and duct connections tightened to stop rattles.
Common fixes and parts
Under-cabinet and chimney hoodsThe most common hoods we repair, with fans and controls reachable from below.
FiltersMesh and baffle grease filters, plus charcoal filters on recirculating hoods.
Island hoods and insertsInserts inside custom covers, serviced through the filter opening.
LightsOlder halogen bulbs or newer LED strips, depending on the hood.
Switches, keypads and boardsMechanical rocker or slide switches on simpler hoods; touch keypads and control boards on newer ones.
Before and after: kitchens near Glenview
Problem
Fixed
DetailA Glenview 1980s two-story: before and after
This one is a 1980s two-story near The Park. Before: almond appliances and a fluorescent box light in the ceiling. What bothered the owners most: a hood that rattled every time it ran. After: the same hood with a new fan motor and working LED lights. The job covered lights and sockets, filter replacement, plus noise and vibration fixes.
Before
AfterRange Hood Repair in a 1980s two-story, Northbrook
This one is a 1980s two-story in Northbrook. The kitchen as it was: black appliances and two hanging glass pendants. The reason for the call: a range hood with dead lights and a weak fan. Finished kitchen: the same hood with a new fan motor and working LED lights. On site this meant blower wheel service, filter replacement, plus noise and vibration fixes.
Range Hood Repair in Northbrook →
Before
AfterDes Plaines kitchen, 1980s two-story: range hood repair
This one is a 1980s two-story in Des Plaines. What we started with: white appliances and a brass chandelier over the nook. The reason for the call: a loud, rattling range hood. After: the same hood with a new fan motor and working LED lights. The job covered blower wheel service, switches and control boards, plus lights and sockets.
Range Hood Repair in Des Plaines →
Before
AfterGlenview kitchen, two-story colonial from the 1990s: residential kitchen hood cleaning
What changed: the same hood with clean, shining filters.
Residential Kitchen Hood Cleaning in Glenview →
Before
AfterGlenview kitchen, 1950s ranch: kitchen remodeling
Finished: cabinets in white uppers and dusty blue lowers with matte black pulls, bright white quartz counters, a terracotta-look square tile backsplash, black-and-white checkerboard tile flooring and recessed lights and under-cabinet LED strips.
Kitchen Remodeling in Glenview →The repair visit
- Describe the problemTell us what the hood does or doesn't do, and send the brand and model from the label inside.
- Diagnosis on siteWe test the hood in place and find the failed part.
- Repair or replaceYou get a written estimate for the repair, or a straight recommendation to replace.
- Fix and testThe part is replaced and the hood tested on every speed and light.
Range Hood Repair questions from Glenview homeowners
When should I replace a range hood instead of repairing it?
When parts are no longer made, when several major parts have failed at once, or when the hood is too small or recirculating and you want better ventilation.
Do you repair all range hood brands?
We work on most residential hood brands, as long as parts are available.
How much does range hood repair cost?
It depends on the part that failed, the hood model and how easy it is to reach. You get a written, itemized estimate after diagnosis.
Why does my range hood fan not work but the light does?
The hood has power, so the problem is in the fan side: switch, board or motor. We test them in order.
Can you replace just the fan motor?
Yes, when a matching motor is available. We fit it, connect it and balance the wheel.
Do I need a permit for range hood repair in Glenview?
It depends on the scope. Glenview's rule in short: Permit required for remodeling/altering a structure, changing the number or location of plumbing fixtures or piping, and new electrical work. We handle the permit when one is needed with Community Development, Inspectional Services Division (Development Center).
Do you work in my part of Glenview?
Yes. Our crews work across Glenview, including The Park, The Glen, The Grove — ZIP 60025, 60026, 60062 — and nearby Northbrook, Park Ridge, Des Plaines.
Working in Glenview
- A lot of Glenview kitchens date from the 2000s. We know these layouts well and what is worth keeping.
- Most Glenview homes are single-family. We protect floors and driveways and leave the site clean every day.
- We know how Community Development, Inspectional Services Division (Development Center) handles kitchen permits and pull them for you.
The ParkThe GlenThe Grove
ZIP 60025ZIP 60026ZIP 60062
Range Hood Repair nearby
Other kitchen services in Glenview
Range Hood InstallationUnder-cabinet, chimney, island and insert hoods, ducted to the outside.
Residential Kitchen Hood CleaningDegreased filters, fan, hood interior and the duct you can reach.
Kitchen RemodelingFull kitchen remodels, from layout to last cabinet pull.
Kitchen Cabinet PaintingFactory-smooth painted cabinets without replacing them.
Cabinet RefacingNew doors and fronts on your existing cabinet boxes.